Toll Free Number : (844) 966-0955

San Diego County: (760) 691-5094

Orange County: (949) 408-1055

Riverside County: (951) 467-4551

Toll Free Number : (844) 966-0955

Home » Blog » How To Maintain Your Water Heater For Optimal Performance

How To Maintain Your Water Heater For Optimal Performance

Water Heater Repair Done by Technicians

Water heaters are essential appliances in our homes, providing hot water for various activities such as showering, cooking, and cleaning. Not only does it provide hot water for showers, laundry, and dishwashing, but it also helps you avoid costly water heater replacement in Brea.

However, like all appliances, water heaters require maintenance to ensure they perform at their best. Neglecting to maintain your water heater can lead to decreased performance, increased energy bills, and, in severe cases, costly repairs.

In this blog post, we’ll discuss how to maintain your water heater for optimal performance in Brea, California. We’ll also provide tips on when it’s time to consider a Water Heater Replacement in Brea and how to choose the right one for your home.

Understanding Your Water Heater

Before we dive into the maintenance steps, it’s important to understand the different types of water heaters and their key components.

There are two main types of water heaters: conventional storage tank water heaters and tankless water heaters. Both types have a heating element, a thermostat, and a temperature and pressure relief valve.

Several factors can affect the performance of your water heater several factors, including the age of the unit, the quality of the installation, and the hardness of your water.

Hard water can cause mineral buildup in the tank, reducing its efficiency and shortening its lifespan.

Knowing When to Repair Your Water Heater

A water heater is an essential appliance in the home and one of the most Important investments you can make.

But, like any other appliance, it will eventually need to be replaced.

When your water heater reaches the end of its lifespan, it’s time to consider a Brea water heater replacement.

Signs that indicate it may be time to replace your water heater include:

Increased energy bills

If you notice your energy bills increasing over time, this may be a sign that your water heater is not working as efficiently as it used to and is costing more to operate.


Most water heaters last around 8-12 years, depending on their type and use. If yours is getting close to this age, it may be time for a replacement.

Corrosion and rust

If you notice rust or corrosion near the bottom of the tank, this is a sign that the protective lining has worn away and the tank is no longer able to contain the hot water.

Water quality

If you’re noticing an increase in sediment in your hot water, this could mean that the tank is deteriorating.


If you hear loud banging or rumbling noises coming from your water heater, it’s likely a sign that something is wrong with the ua professional should check it a professional.

If you’re noticing any of these signs, it’s Important Points to consider water heater replacement. A qualified professional can assess your current system and advise you if a replacement is necessary or if repairs would suffice.

How To Maintain A Water Heater

Conduct general inspections at least every two months

  • Check the water pressure
  • Check water flow (if you have a tankless system)
  • Check the venting system for leaks
  • Locate and replace any corroded or damaged parts

Every one to two years, flush the water heater

  • Use a flushing kit to flush out sediment in your tank.
  • Turn off the gas or electricity supply to your water heater.
  • Open the drain valve and let out any remaining water.
  • Drain any standing water from the bottom of the tank and close the drain valve.
  • Attach a garden hose to an outside faucet and run cold water through it until there is no more standing water in your tank.

Check the Anode Rod

  • Check the condition of the anode rod. If it is corroded or bent, replace it.
  • Anode rods can be removed by opening the access panel on your water heater and unscrewing them from their housings with a spanner wrench.
  • Replace anode rods with new ones every few years, or whenever they are visibly corroded or bent.

Annual Temperature and Pressure (T&P) Valve Testing

The T&P valve is a safety device that prevents your water heater from exploding if its pressure rises too high.

  • To test this valve, first turn off the electricity to your water heater at the breaker box.
  • Next, remove the T&P valve from your water heater by unscrewing it with a wrench.
  • Fill a bucket with cold water and set it next to your water heater.
  • Turn on the hot-water tap for about 15 seconds until you see steam coming out of it —this means that the T&P valve is working properly.
  • Next, turn off the hot-water tap and slowly open the T&P valve until water starts to drip from it.
  • When you have about 1/4 cup of water in your bucket, close the valve again.

Verify the thermostat’s settings

  • Turn the hot and cold water taps on, one at a time.
  • Wait for them to warm up, then turn them off.
  • Feel the temperature of each tap with your hand; if you can feel the heat coming out of either one, it means that your thermostat is working properly.
  • If you can’t feel the heat coming out of either tap, your thermostat is broken.

Insulate the Tank

If you live in an area with cold winters, you may want to insulate your water heater tank.

The best way to do this is by placing it inside a small shed outside or wrapping it in blankets or sheets of foam insulation.

If you’re going to insulate your water heater, be sure that it’s protected from the cold. If not, the insulation could cause a fire.

If you live in a warm climate, insulating your tank isn’t necessary. You can probably skip this step if you’re just starting out with your water heater.

Check for Leaks

If there are cracks or leaks on the outside of your tank, it could be leaking inside as well. This is especially important to check if you live in an area where freezing temperatures are common during winter months; otherwise, any cracks could freeze and expand leading to even more damage to your water heater.

Check for Corrosion

If you see a buildup of rust on your tank, it could be corroding from the inside out. This is especially important to check if you live in an area where freezing temperatures are common during winter months; otherwise, any cracks could freeze and expand leading to even more damage to your water heater.

Ensure that the ventilation is effective

You can check if your water heater has adequate ventilation by looking for a fan or exhaust pipe. If you don’t see one, make sure to install one as soon as possible

The fan needs to be in place so that when the water inside your tank heats up and expands, it doesn’t trap all of the hot air inside. This can cause pressure buildup and lead to dangerous leaks or explosions.

When leaving, lower the thermostat settings

When you are going out of town for a few days, it’s a good idea to lower your water heater’s temperature setting.

The reason for this is that if the water in your tank freezes and expands, it could damage the tank.

If you don’t want to be stuck with a costly repair bill when you return from your vacation, simply adjust the thermostat before leaving.

Water heater replacement in Brea is an option when all the suggestions are applied and yet, your water heater is still not functioning


Maintaining your water heater is key to optimal performance, but you may eventually need to replace it. If your water heater is too old, damaged, or leaking, you should consider a water heater replacement in Brea.

You can easily find a plumber in Brea who will help you choose the right model for your home, install it correctly, and offer regular maintenance services.

Be sure to research the available options, compare prices, and read reviews before making a purchase.

Our team takes all COVID precautionary measures while working.